Contact us: 1-855-200-TEST (8378) or sales@testworld.com

Sorensen XG 40-38, 1U Programmable DC Power Supplies, 40 Volts, 38 Amps

Sorensen XG 40-38, 1U Programmable DC Power Supplies, 40 Volts, 38 Amps

Description

The Sorensen XG 40-38, 1U Programmable DC Power Supplies, 40 Volts, 38 Amps Introducing the XG series DC power supply from Sorensen offering maximum power in a 1U chassis.The XG features the most widely used digital and analogue interconnects, so it is quick and inexpensive to connect multiple XGs together.Using the highest performance soft-switching technology, its output of 1500 watts represents the highest power density available anywhere.

Key Features: Sorensen XG 40-38 :

  •    Industry Leading Power Density  : 1520 Watts
  •   High power densit
  •    Soft-switching technology
  •   Comprehensive digital and analog interface options
  •     Scalable, multi-unit design linkable via RS485
  •   USB and RS232 interfaces standard, further
  • interfaces optional
  • Bus controlled Auxiliary 5V/15V output
  •   Built-in program sequencing
  • Auto sleep-mode after period of non-use

Easy Integration
The Sorensen XG 40-38, 1U Programmable DC Power Supplies, 40 Volts, 38 Amps has many control and indication signals such as shutdown, constant voltage (CV) vs. constant current (CC) mode indication, OVP, OCP, OTP, and so on. In addition, the logical-high or -low is free selectable. Thus enabling this model to replace existing power supplies with little or no system engineering required.

Free selectable analog control range
Most DC power supplies provide a 0 to 5 or 0 to 10 V analog control range to control the DC output from zero to full DC output range. With this model, the analog control range is free selectable starting at 0V to an upper range between 2V and 10V. In other words, the analog
programming interface range is freely adjustable.

Auxiliary DC output channels with control
In many ATE systems one or more low power, fixed voltage supplies are needed to provide electrical power for any periphery within the ATE cabinet. For this purpose, this model provides two standard auxiliary DC output channels. Both auxiliary power channels are controllable
directly from the front-panel or through SCPI commands. With these channels, it is possible to drive outputdisconnect or polarity-reversal relays, without needing a complicated computer controlled relay board.

DC-waveforms through internal sequencing
To allow for extremely fast programming, sequences can be programmed into and stored in memory using standard SCPI commands through USB, RS-232/485, LXI or GPIB.

Variable Fan Speed Control
The Sorensen XG 40-38, 1U Programmable DC Power Supplies, 40 Volts, 38 Amps innovative approach to fan speed is determined by internal heat sink temperature. This allows the fans to adjust to a constant optimal speed when the output of the supply is being pulsed. This also reduces noise and increases fan life.

Power Saving Standby Mode
When this model has been in an idle state, the supply can go into “sleep mode”, much like a computer monitor. This will allow the user to save energy and minimize lab noise. Since this model left in sleep mode is still “on” the user will have quicker access to an enabled output.

Key Modes
Output Auto Start Mode (Auto Restart)
The Auto Start mode establishes the state of the output of the power supply after recovery from a complete power cycle (all front panel LEDs are not illuminated), or after recovery from a PC failure or reboot. If Auto Start mode is set to On, the power supply output will return to its previous value. Also, after the loss of any remote digital control, the model will remain active in its last programmed setting and will not disrupt any test process.

Auxiliary Auto Start Mode
The Auxiliary Auto Start mode determines the state of the auxiliary output after a complete power cycle (all front panel LEDS are not illuminated). With Auxiliary Auto Start mode turned to On, the auxiliary output will be activated after the power supply is powered up again.

Foldback Mode
Foldback mode is used to disable the output when a transition is made between the operating modes. The power supply will turn off/disable the output and lock in foldback mode after a specified delay if the power supply transitions into CV mode or into CC mode, depending on the foldback mode settings. This feature is particularly useful for protecting current or voltage sensitive loads. Foldback can be set to trigger a switch when transitioning from CV to CC mode or from CC to CV mode.

Reviews

There are no reviews yet.

Be the first to review “Sorensen XG 40-38, 1U Programmable DC Power Supplies, 40 Volts, 38 Amps”