Contact us: 1-855-200-8378 or sales@testworld.com
Search
Generic filters

Sencore LC102 AUTO-Z Capacitor-Inductor Analyzer

Sencore LC102 AUTO-Z Capacitor-Inductor Analyzer

Category:

Description

Sencore LC102 AUTO-Z Features

  • Analyzes capacitors for:
    •  Value from 1 pF to 20 F
    •  Leakage with up to 1 kV applied
    •  Dielectric absorption
    •  Equivalent series resistance (ESR)
  • Analyzes inductors from 1 uH to 20 H for opens, shorts, value, and even one shorted turn
  • Analyzes SCRs and triacs (with accessory), high-voltage resistors, and transmission lines
  • Makes all tests, compares results to EIA standards, and tells you “GOOD” or “BAD” – automatically
  • Portable; 9-hour battery operation for remote sites – AC operation for your bench

Sencore LC102 AUTO-Z Condensed Specifications

Capacitor Value – RANGE: 1.0 pF to 19.99 F fully autoranged. ACCURACY: ±1% ±1 pF ± 1 digit up to 1990 uF. ± 5% ± .1% of range fullscale for 2000 uF to 19.99 F. Resolution: .1 pF on lowest range to .01 F on highest range: 12 ranges total. Automatically reads GOOD or BAD according to tolerance selected on keypad. Double layer lytics test patented.

Capacitor Leakage Voltage – VOLTAGE RANGE: 1.0V to 999.9V in 0.1V steps.

VOLTAGE ACCURACY: +0% -5% POWER: Short circuit current limited to < 900 mA. Continuous power limited to 6 watts ± 10%. Selected on keypad.

Capacitor Leakage (current- RANGE: 0.01 uA to 19.99 mA fully autoranged. ACCURACY: ±5% ±1 digit.

RESOLUTION: 0.01 uA to .01 mA for 0.01 uA to 19.99 mA in four ranges. VOLTAGE: Maximum reading determined by voltage setting.

As A Dynamic Ohmmeter – RANGE: 100 ohms to 999 megohms depending on voltage setting.

ACCURACY: ±5% ± 1 digit.

Capacitor Dielectric Absorption Test – RANGE: 1 to 100%. ACCURACY: ±5% of reading, ± 1 digit. CAPACITOR RANGE: 0.01 uF to 19.99 F. Automatically reads GOOD or BAD on electrolytics at 15 percent variation in reading after charge and discharge; less for other capacitors.

Capacitor Equivalent Series Resistance (ESR) – RANGE: 0.10 ohm to 1999 ohms fully autoranged.

ACCURACY: ±5% ± 1 digit. RESOLUTION: .01 ohms to 1 ohm on high end in three ranges.

CAPACITOR RANGE: 1 uF to 19.99 F.

Inductor Value – RANGE: 0.10 uH to 19.99 H fully autoranged. ACCURACY: ±2% ± 1 digit.

RESOLUTION: .01 uH for 20 uH range to .01 H for 19.99 H range: 9 automatic ranges.

Ringing Test – Excites inductor with sharp wavefront of 5 volts peak amplitude 60 Hz. ACCURACY: ± 1 count from readings of 8 to 13: 10 rings or more automatically indicated as GOOD. Automatically selects correct impedance match to produce maximum rings. RESOLUTION: ± 1 digit.

General – DISPLAY: 6 digit LCD: auto decimal placement; leading zero suppression; pF, uF, F, uA, mA, %, K ohm, M ohm, ohms, uH, mH, H, V, RINGS, SHORT, OPEN, WAIT, GOOD, and BAD annunciators, overranged indication. POWER: 105-135 VAC 60 Hz with supplied PA251 power adapter. Battery with optional BY234, 2.0 AH battery for 9 hours continuous typical battery life. Auto off approximately 20 minutes after use. Auto off overidden when using external AC power. SIZE AND WEIGHT: 6″ x 9″ x 11.5″ HWD (15.2 x 22.6 x 29.2 cm.). 6 lbs. (2.7 kg.) without battery. 7.6 lbs. (3.5 kg.) with battery.

Reviews

There are no reviews yet.

Be the first to review “Sencore LC102 AUTO-Z Capacitor-Inductor Analyzer”

Your email address will not be published. Required fields are marked *