Contact us: 1-855-200-8378 or sales@testworld.com
Exact matches only
Search in title
Search in content
Search in comments
Search in excerpt
Search in posts
Search in pages
Search in groups
Search in users
Search in forums
Filter by Custom Post Type
product
Filter by Categories
News and Information

Agilent E4416A RF Power Meter for GSM, EDGE, NADC, iDEN, Bluetooth, IS-95 CDMA, W-CDMA and cdma2000

Agilent E4416A RF Power Meter for GSM, EDGE, NADC, iDEN, Bluetooth, IS-95 CDMA, W-CDMA and cdma2000

Description

Specifications describe the instrument’s warranted performance and apply after a 30 minute warm-up. These specifications are valid over its operating and environmental range unless otherwise stated and after performing a zero and calibration procedure.

Supplemental characteristics are intended to provide additional information; useful in applying the instrument by giving typical (expected), but not warranted performance parameters. These characteristics are shown in italics or labeled as ‘typical’, ‘nominal’ or ‘approximate’.

Measurement uncertainties information can be found in, Fundamentals of RF and Microwave Power Measurements-Application Note 64-1, literature number 5965-6630E.

Compatibility, the Agilent E4416A RF Power Meter for 1xEV-DO Wireless Communications System power meters operate with the E-series E9320 family of power sensors for peak, average and time-gated power measurements. The Agilent E4416A RF Power Meter for 1xEV-DO Wireless Communications System also operates with the existing 8480 and N8480 series, E-series CW and the E9300 range of power sensors for average power measurements.

Measurement modes, the Agilent E4416A RF Power Meter for 1xEV-DO Wireless Communications System series power meters have two measurement modes:

  •  Normal mode (default mode using E9320 sensors) for peak, average and timerelated
    measurements, and
  •  Average only mode. This mode is primarily for average power measurements
    on low-level signals, when using E9320 sensors, and is the mode used with
    8480 and N8480 series sensors, E-series CW sensors and E-series E9300
    sensors.

Frequency range: 9 kHz to 110 GHz, sensor dependent
Power range: -70 to +44 dBm, sensor dependent

Key Features & Specifications

  • 20 Msample/s per second sampling rate for reliable continuous and single shot measurements on wide bandwidth signals
  • Time-gated and free run power measurements
  • Free ´Analyzer Software´ software for complete pulse and statistical analysis, software is located ´In the Library´
  • 8 pre-defined wireless configurations (GSM, EDGE, NADC, iDEN, Bluetooth™, IS-95 CDMA, W-CDMA and cdma2000)

Description

The E4416A single channel EPM-P series power meter, for peak, average, peak-to-average ratio and time-gated measurements, using the E9320 peak and average power sensors.

  • 20 Msample/s per second sampling rate for reliable continuous and single shot measurements on wide bandwidth signals
  • Time-gated and free run power measurements
  • Free ‘Analyzer Software’ software for complete pulse and statistical analysis, software is located ‘In the Library’
  • 8 pre-defined wireless configurations (GSM, EDGE, NADC, iDEN, Bluetooth™, IS-95 CDMA, W-CDMA and cdma2000)

1xEV-DO wireless systems — simplify development, verification, and manufacturing with the EPM-P power meters and E9320 E-Series power sensors

Reviews

There are no reviews yet.

Be the first to review “Agilent E4416A RF Power Meter for GSM, EDGE, NADC, iDEN, Bluetooth, IS-95 CDMA, W-CDMA and cdma2000”

Your email address will not be published. Required fields are marked *